Under "connect" I select CAT and then "Start". The green light on the bottom turns on. But the window for the Frequency display says :off.
Any suggestions?
Art K0AY
Can't get CAT to work
Re: Can't get CAT to work
I also cannot get CAT to work. Rig 1 FT950
Rig 2 FT857D
When I set up V2.4.0 I tried hmalib for rig control was not able to anything working. Tried Omni rig v1.19 and found that neither of my radios are listed. Rig 1 was able to connect to the Log40M-2 as an FTDX-1200. Rig 2 nothing.
Omnirig lists both radios as supported but they are listed in omni rig screen on "show CAT interface " screen. I have check baud rates for both radios to make sure they are match computer settings. Thanks for any assistance here. I have been using the other version of Log40m and really like it. Hope to get this version working.
Thanks
AC8JW
Rig 2 FT857D
When I set up V2.4.0 I tried hmalib for rig control was not able to anything working. Tried Omni rig v1.19 and found that neither of my radios are listed. Rig 1 was able to connect to the Log40M-2 as an FTDX-1200. Rig 2 nothing.
Omnirig lists both radios as supported but they are listed in omni rig screen on "show CAT interface " screen. I have check baud rates for both radios to make sure they are match computer settings. Thanks for any assistance here. I have been using the other version of Log40m and really like it. Hope to get this version working.
Thanks
AC8JW
- G4POP
- Log4OM Alpha Team
- Posts: 10803
- Joined: 21 Jan 2013, 14:55
- Location: Burnham on Crouch, Essex UK
Re: Can't get CAT to work
If you have version 1 working ok with Omnirig controlling both of your radios then providing you have selected Omnirig in version 2 and checked the auto connect box in the cat config then no changes to Omnirig should be required.
Unless of course you have other programs connected to the radio also?
Unless of course you have other programs connected to the radio also?
73 Terry G4POP
Re: Can't get CAT to work
version 1.4 was deleted. Hamlib does not connect and radios are not listed in Omnirig list. No other program is using either radio.
- G4POP
- Log4OM Alpha Team
- Posts: 10803
- Joined: 21 Jan 2013, 14:55
- Location: Burnham on Crouch, Essex UK
Re: Can't get CAT to work
Both of your radios are listed in Omnirig, as shown below, I suggest you download the rig list from Omnirig again
73 Terry G4POP
- DF5WW
- Log4OM Alpha Team
- Posts: 2035
- Joined: 02 May 2013, 09:49
- Location: Kraam, Rhineland Palatinate, Germany
- Contact:
Re: Can't get CAT to work
If you not have listed them go to Omnirig download page and download
the rig.ini files. They are not included when you download omnirig from
that page. You have to download seperatly.
the rig.ini files. They are not included when you download omnirig from
that page. You have to download seperatly.
73´s .. Juergen ... ALT-512 SDR (10W) , 50 m random wire at SG-211 autotuner, 2 x Xiegu G90 (20W HF TRX) one as portable Radio. Also TS-790E (40 W) for VHF/UHF with X-50 vertical and Duoband 4-Element LPDA.
Re: Can't get CAT to work
OK and thank you for that. Did find the ini file. Where does it get extracted to? The folder with omnirig?
Re: Can't get CAT to work
OK got it working. Needed to delete omni rig and download the ini file. Then reinstalled Omni rig and all was well. Thank you for the help.
73.
73.