IC-7600v2 with Omni-Rig

General discussions V2
Post Reply
F5OWK
Novice Class
Posts: 8
Joined: 20 May 2013, 21:09

IC-7600v2 with Omni-Rig

Post by F5OWK »

Hi,

Omni-Rig (V 1.19) seems seems not to recognize IC-7600v2.

No problem with HRD and, of course, I've tried to use with Omni-Rig the same port and baud rate than HRD !

Of course alos, the IC-7600 driver was installed before connecting the transceiver.

So, I have no more idea :(

Who can help me ?

Thanks in advance. 73 QRO.

Herve
User avatar
G4POP
Log4OM Alpha Team
Posts: 10753
Joined: 21 Jan 2013, 14:55
Location: Burnham on Crouch, Essex UK

Re: IC-7600v2 with Omni-Rig

Post by G4POP »

My 7600 worked fine with Omnirig are you sure the baud rate and com port match and is the Icom C-IV address the default Icom one or did you change it?
73 Terry G4POP
User avatar
IK0TIX
Advanced Class
Posts: 87
Joined: 26 Mar 2016, 06:41

Re: IC-7600v2 with Omni-Rig

Post by IK0TIX »

Herve,
this is my setting for 7610, it's the same of my old 7600:
Cattura.JPG
Cattura.JPG (31.59 KiB) Viewed 3903 times
73
Max IK0TIX
User avatar
G4POP
Log4OM Alpha Team
Posts: 10753
Joined: 21 Jan 2013, 14:55
Location: Burnham on Crouch, Essex UK

Re: IC-7600v2 with Omni-Rig

Post by G4POP »

But are you sure the radio Baud rate is set to 115200 and that the CAT control is set to either USB or ACC according to what you are using.

Did you set CAT to auto start in Program Configuration/CAT?

Are you certain that no other program is using the com port?

It will be a miss-match or menu setting somewhere because I have two friends using the 7610 and neither have issues with Log4OM V2 using Omnirig

I currently have an IC7300 and a 7100 using Omnirig and previously had the 7600 and all work flawlessly.
73 Terry G4POP
F1SMV
Advanced Class
Posts: 42
Joined: 15 Mar 2014, 18:33

Re: IC-7600v2 with Omni-Rig

Post by F1SMV »

Bonjour

test your connexion in first with commander from dx labs software to see more setup. This soft run very well with all trx. After test omnirig.

73 Eric

ps : i have too icom 7600 which run well with omnirig
User avatar
IK0TIX
Advanced Class
Posts: 87
Joined: 26 Mar 2016, 06:41

Re: IC-7600v2 with Omni-Rig

Post by IK0TIX »

G4POP wrote: 07 Feb 2020, 00:13 But are you sure the radio Baud rate is set to 115200 and that the CAT control is set to either USB or ACC according to what you are using.

Did you set CAT to auto start in Program Configuration/CAT?

Are you certain that no other program is using the com port?

It will be a miss-match or menu setting somewhere because I have two friends using the 7610 and neither have issues with Log4OM V2 using Omnirig

I currently have an IC7300 and a 7100 using Omnirig and previously had the 7600 and all work flawlessly.
Terry, I have no problems with my 7610. Omnirig and log4om v2 work great for me. Mine was an advice to Eric because for my 7610 (except the baud) I use the same settings that I used for my 7600 ;)
73
Max IK0TIX
Post Reply