Page 1 of 1

Callsigns in Cluster Scanner not clickable

Posted: 20 Aug 2018, 14:01
by oe3ide
Hey,
I have some weird issue since a couple of weeks. If I click a callsign in the cluster scanner window, nothing happens. Normaly simple click should pick the callsign into the callsign field, doubleclick should additionally change freq/mode.

See video: https://www.oe3ide.com/wordp/wp-content ... -45-25.mkv

Re: Callsigns in Cluster Scanner not clickable

Posted: 26 Aug 2018, 20:58
by oe3ide
I found the "problem" or reason. I am running also SDR Console V3 (also connected via OmniRig). If I close SDR Console, all works normal...
There seams to be an issue with this kind of setup.

73 Ernst

Re: Callsigns in Cluster Scanner not clickable

Posted: 27 Aug 2018, 05:40
by G4POP
Install all three programs to run as an administrator by right clicking the instal file and selecting 'run as an administrator'

Re: Callsigns in Cluster Scanner not clickable

Posted: 27 Aug 2018, 10:11
by oe3ide
Thanks Terry,

already installed & running as Admin... I do this for all applications communicating via cat (direct or omnirig).

I posted this issue also on sdrradio groups, because it only appears with Console V3.
All runs fine with Console V2.3, HDSDR, SDRUno.

I will update this thread, if I (or Simon) have a solution.

73 Ernst

Re: Callsigns in Cluster Scanner not clickable

Posted: 27 Aug 2018, 11:16
by G4POP
oe3ide wrote: 27 Aug 2018, 10:11 Thanks Terry,

already installed & running as Admin... I do this for all applications communicating via cat (direct or omnirig).

I posted this issue also on sdrradio groups, because it only appears with Console V3.
All runs fine with Console V2.3, HDSDR, SDRUno.

I will update this thread, if I (or Simon) have a solution.

73 Ernst
Ernst,
I just checked and SDR-Radio Consul version 3.0.2 build 1234 works fine for me with Log4OM using Omnirig on both of the radios that I have connected.


My only issue with SDR-Radio Consul is that it does not support my Elecraft KX3 I/Q output so I have to use my RFSpace SDR-IP receiver as a Panadaptor :(

Do you have the latest version of Omnirig installed?

Re: Callsigns in Cluster Scanner not clickable

Posted: 27 Aug 2018, 18:15
by oe3ide
Ok, Omnirig is the newest one 1.16.

Now I did a install with admin-rights for Log4OM (1.33.1.0), OmniRig & SDRRadio 3.0.2.

Will check it and the next days..

73 Ernst

Re: Callsigns in Cluster Scanner not clickable

Posted: 27 Aug 2018, 20:43
by oe3ide
Ok, running this setup ~2h shows the same issue... spots in bandmap are not clickable, on 3rd or 4th attempt finally the callsign goes into the inputbox.
Delay of about 2-3 s on clicking spots in the cluster window.

If I switch off/on the tracking in SDR Console, all works normal, at least for a few minutes. After then it starts again.

I am using the Omnirig-Setting FT2000 PEP V3 with this mod:

Code: Select all

[STATUS6]
Command=(TX;)
ReplyLength=4
ReplyEnd=(;)
Validate=(TX.;)
Flag1=(..0.)|pmRX
Flag2=(..1.)|pmTX
Flag3=(..2.)|pmTX
original:

Code: Select all

[STATUS6]
Command=(TX;)

ReplyEnd=(;)
Validate=(TX.;)
Flag1=(..0.)|pmRX
Flag2=(..1.)|pmTX
I need this mod, because with the original ini-file, Omnirig does'nt recognize TX, and so SDR Radio does not mute or reduce IQ data.

73 Ernst

Re: Callsigns in Cluster Scanner not clickable

Posted: 02 Nov 2018, 09:12
by G4POP
Having spoken to Simon who develops SDR Radio Consul because I discovered the same shortcoming with Omnirig connections.

It appears that you must use a VSP to connect Log4om directly to SDR Radio Consul and SDR CONSUL connects to your radio via Omnirig

I find this a bit limiting because I don't like having to constantly change com ports but at this time it appears that Simon's software does not fully support the multi threading capability of Omnirig.

Re: Callsigns in Cluster Scanner not clickable

Posted: 06 Nov 2018, 22:08
by oe3ide
OK, thanks for the update.
I will give it a try with VSPE.

73