Search found 13 matches
- 16 May 2022, 08:34
- Forum: Error reports
- Topic: QSO Distance always in km - regardless of config setting
- Replies: 6
- Views: 1735
Re: QSO Distance always in km - regardless of config setting
I mean in the QSOs tab at the bottom. Why can’t those distances be converted into miles?
- 15 May 2022, 20:31
- Forum: Error reports
- Topic: QSO Distance always in km - regardless of config setting
- Replies: 6
- Views: 1735
Re: QSO Distance always in km - regardless of config setting
So what’s the point of the distance setting? Can’t the app convert km into miles?
Regards,
Simon
Regards,
Simon
- 15 May 2022, 11:01
- Forum: Error reports
- Topic: QSO Distance always in km - regardless of config setting
- Replies: 6
- Views: 1735
Re: QSO Distance always in km - regardless of config setting
I’ve noticed the same, using 2.21.1.0 here. Distance is always displayed in km, even though set to miles.
73, M7WWX
73, M7WWX
- 12 Apr 2022, 08:50
- Forum: User support
- Topic: Omnirig Rig Control Error
- Replies: 11
- Views: 1889
Re: Omnirig Rig Control Error
Terry and Juergen, Many thanks for your replies. I have done some research and believe that is what I need? https://www.hamradio.co.uk/accessories-by-manufacturer-ldg-accessories-ldg-accessories/ldg/ldg-ru-1-1-unun-pd-10250.php?utm_source=Froogle&utm_medium=Froogle&utm_campaign=Froogle&g...
- 11 Apr 2022, 14:24
- Forum: User support
- Topic: Omnirig Rig Control Error
- Replies: 11
- Views: 1889
Re: Omnirig Rig Control Error
No, that’s just a phone photo of the computer screen! There is no interference on the monitor at all.
Thanks for the advice.
73, M7WWX
Thanks for the advice.
73, M7WWX
- 11 Apr 2022, 10:01
- Forum: User support
- Topic: Omnirig Rig Control Error
- Replies: 11
- Views: 1889
Re: Omnirig Rig Control Error
Diamond BB7V vertical
17m Ultraflex 7 feeder
Xiegu G90 with CE-19 interface
Thanks I’ll look into it.
73, Simon (M7WWX)
17m Ultraflex 7 feeder
Xiegu G90 with CE-19 interface
Thanks I’ll look into it.
73, Simon (M7WWX)
- 11 Apr 2022, 09:25
- Forum: User support
- Topic: Omnirig Rig Control Error
- Replies: 11
- Views: 1889
Re: Omnirig Rig Control Error
I have ferrited everything, both ends of all cables in and out of my transceiver and PC.
73, Simon
73, Simon
- 11 Apr 2022, 08:36
- Forum: User support
- Topic: Omnirig Rig Control Error
- Replies: 11
- Views: 1889
Omnirig Rig Control Error
More Omnirig woes… I constantly get the attached error when working FT8, especially in the higher frequencies. 40m is the mosr stable, 20m and above less so. It breaks the transmission routine. Clicking Retry sometimes allows me to carry on, other times I have to switch to lower frequencies. Any ide...
- 07 Apr 2022, 14:58
- Forum: User support
- Topic: CAT control via Omnirig (Xiegu G90)
- Replies: 9
- Views: 2639
Re: CAT control via Omnirig (Xiegu G90)
I realise that Terry. Was just highlighting that on the 2-tab version, Omnirig works with 1 or 2 stop bits selected, and RTS and DTR set to low or high. I wondered what effect these settings have. Shouldn’t have included the Swiss screenshot, but the settings highlighted also work on the older versi...
- 07 Apr 2022, 10:31
- Forum: User support
- Topic: CAT control via Omnirig (Xiegu G90)
- Replies: 9
- Views: 2639
Re: CAT control via Omnirig (Xiegu G90)
Thanks Juergen,
I’ve seen you post these settings before.
In fact both these seem to work equally well.
Do you know what the differences mean?
73, Simon
I’ve seen you post these settings before.
In fact both these seem to work equally well.
Do you know what the differences mean?
73, Simon