Log4OM

With Log4OM V2, using OmniRig 1.9 for CAT control, can I force the "rig" setting in Log4OMv2 to use only Rig 1 ?
For my install the setting changes to Rig 2 quite often when i am not watching it and that kills the other software using the OmniRig port 2. Log4OM is usually minimized. When I see SDRuno not responding I switch to Log4OM and find it has switched to "rig 2".

I have SDRUNO using omniRig port2 for its sync options.
I do have my windows 10 desktop mouse settings to
"scroll inactive windows when mouse over" set to ON. ( In case it is relevant to this problem)

I have not found any place that I can force Log4OM to stay on Rig1 and not move.

Thanks for any suggestions.
Kevin / K7SW

K7SW wrote: 31 Jan 2020, 06:20 With Log4OM V2, using OmniRig 1.9 for CAT control, can I force the "rig" setting in Log4OMv2 to use only Rig 1 ?
For my install the setting changes to Rig 2 quite often when i am not watching it and that kills the other software using the OmniRig port 2. Log4OM is usually minimized. When I see SDRuno not responding I switch to Log4OM and find it has switched to "rig 2".

I have SDRUNO using omniRig port2 for its sync options.
I do have my windows 10 desktop mouse settings to
"scroll inactive windows when mouse over" set to ON. ( In case it is relevant to this problem)

I have not found any place that I can force Log4OM to stay on Rig1 and not move.

Thanks for any suggestions.
Kevin / K7SW

Kevin,

I had Doug move your post to the V2 section as it will have more visibility here as your question relates to the new V2 of Log4OM2.

K7SW wrote: 31 Jan 2020, 06:20 With Log4OM V2, using OmniRig 1.9 for CAT control, can I force the "rig" setting in Log4OMv2 to use only Rig 1 ?
For my install the setting changes to Rig 2 quite often when i am not watching it and that kills the other software using the OmniRig port 2. Log4OM is usually minimized. When I see SDRuno not responding I switch to Log4OM and find it has switched to "rig 2".

I have SDRUNO using omniRig port2 for its sync options.
I do have my windows 10 desktop mouse settings to
"scroll inactive windows when mouse over" set to ON. ( In case it is relevant to this problem)

I have not found any place that I can force Log4OM to stay on Rig1 and not move.

Thanks for any suggestions.
Kevin / K7SW

What is SDRUno using Omnirig to Sync to?, I use SDRUno, Omnirig and Log4OM with two rigs but do not experience the issue that you describe

Terry,
I was using SDRUno as OmniRig port 2
and Log4OM as OmniRig Port 1

Log4OM would would select OmniRig port 2 and silently conflict with SDRUno.
So I moved SDRuno to Com 15 and disabled Omnirig integration for SDRuno

It is complicated, but this is what I do.
VSP ports are set as "Paired" ports
com 15 and 16
com 17 and 18
com 19 and 20
===================
TenTec OmniVII radio is on Com 8 or Ethernet.
SDRUno com15 to com16 on N4PY port
Log4OM Omnirig #1 -com17 to com18 to N4PY port.
FLDGI via TCP to flrig com19 to com20 N4PY port

K7SW wrote: 02 Feb 2020, 05:43 Terry,
I was using SDRUno as OmniRig port 2
and Log4OM as OmniRig Port 1

Log4OM would would select OmniRig port 2 and silently conflict with SDRUno.
So I moved SDRuno to Com 15 and disabled Omnirig integration for SDRuno

It is complicated, but this is what I do.
VSP ports are set as "Paired" ports
com 15 and 16
com 17 and 18
com 19 and 20
===================
TenTec OmniVII radio is on Com 8 or Ethernet.
SDRUno com15 to com16 on N4PY port
Log4OM Omnirig #1 -com17 to com18 to N4PY port.
FLDGI via TCP to flrig com19 to com20 N4PY port

There is no reason that Log4OM would change from Omnirig rig 1 to rig 2 without external intervention so my best guess it that there is some conflict on the other program which I cant help with because I know nothing about it

Thanks Terry,
This morning I think I have found the offending program. OmniRig 1.19 itself.

With Log4OM V2 open, if you also open "OmniRig" and then close OmniRig.
Log4OM changes OmniRig ports.

I can duplicate this problem each and every time that I open OmniRig..
No need to make changes to OmniRig, just open and then Close OmniRig.
Kevin

Switching occurs ANY time I open OmniRig and then close the program.
If I have another program that wants to use Omnirig port 2, that must do something to start and stop the service which is why I could not figure the problem out..
Without a doubt, I open and close the OmniRig program and Log4OM will switch from Port1 to Port2.

Does this description help ?
===========================================
Log4OM, Now that I know what the symptom is, I have tested by having Log4OM v2 select Rig2.
When I open and close OmniRig now, Log4OM will stay
on OmniRig Port 2..

When Log4OM v2 starts it wants port1 of OmniRig. As long as I Open Omnirig and close it again, Log4OM v2 appears to switch and stay on Port 2 from that point on.